Détails du produit
50 Ohm 10 Watts Black Anodized Aluminum Heatsink 7/16 DIN Female RF Load Up To 7 GHz
Référence (MPN)
Impédance
50 Ohm
Fréquence
DC
Interface
7/16 DIN
câble RF sur mesure depuis plan pour sourcing de production
câble RF sur mesure depuis plan orienté production avec revue de compatibilité, guidance MOQ et support de sourcing cost-down.
Quoi préparer avant le RFQ Des données claires réduisent les hypothèses et accélèrent la réponse. ⌄
- • Partagez le MPN de référence, la pièce homologue ou la marque source si c’est important pour la vérification.
- • Ajoutez le BOM, la répartition des quantités et la demande annuelle si le projet dépasse le volume prototype.
- • Joignez le plan, la fiche technique ou les exigences critiques d’impédance, fréquence, montage et revêtement.
Image
Cliquez pour agrandir.
Specifications
| Interface | Terminations |
|---|---|
| Interface | RF Load |
| Interface | 7/16 DIN |
| Impédance | 50 Ohm |
| Fréquence (max) | DC |
| Fréquence (max) | 7 GHz |
| Genre | Female |
| Maximum VSWR | 1.25:1 |
| Maximum Power | 10 Watt |
| Category | Terminations |
Description
Données de référence actuelles pour PE6141 : 7/16 DIN · 50 Ohm · DC. Le catalogue indique la configuration suivante : RF Load. L’impédance est indiquée comme 50 Ohm. Si ce paramètre est critique, confirmez-le à nouveau dans le RFQ. La fréquence est indiquée comme DC. La limite réelle dépend toujours de l’assemblage, de la pièce homologue et du contexte d’application. Si le montage manque ici, confirmez-le à partir du plan ou de l’exigence d’accouplement. Utilisez cette page pour présélectionner avant le RFQ, pas comme validation finale.
Utilisez cette page pour présélectionner avant le RFQ. Le parcours d’approvisionnement et la production sur mesure MOQ 200+ sont confirmés après examen du plan/de la spécification/du BOM.
Connecteurs similaires
Ces modèles peuvent aussi vous intéresser :
LCCA30189-FT3
L-com's LCCA30189-FT3 is a low loss 4.3-10 male to 4.3-10 male cable assembly using LMR-400 coax, 3 FT with Times Microwave components and ships same-day. The LMR-400 coax of this 4.3-10 cable uses the PE (F) dielectric with a VoP of 85%, resulting in very low insertion loss compared to solid dielectrics. These flexible RF cable assemblies are ideal for applications where flexure is required. Our L-com 4.3-10 to 4.3-10 cable assembly has a male to male gender configuration with flexible LMR-400 series coax and operates to 6 GHz. The double shield of this 4.3-10 cable is layered by tinned copper braid over aluminum tape providing shielding effectiveness greater than 90dB. *LMR™ is a trademark of Times Microwave Systems. Custom versions of this 4.3-10 male to 4.3-10 male cable, along with the rest of L-com's other RF assemblies, can also be built and shipped same day. Other available RF cable assembly value added services from L-com include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for testing or custom RF cable quotes. Part number LCCA30189-FT3 L-com Low Loss 4.3-10 Male to 4.3-10 Male Cable Assembly using LMR-400 Coax, 3 FT with Times Microwave Components data sheet PDF includes details of the RF product specifications, CAD drawing(s) and dimensions below.
LCCA30008-FT1
L-com Cable Assembly LCCA30008 is an N male to N female 1 foot cable using 402SS Series coax that ships same-day. L-com's flexible RF cable assemblies are ideal for applications where tight bends and flexure are required. This L-com N to N cable assembly has a male to female gender configuration with 50 ohm flexible 402SS Series coax and operates to 18 GHz. Highly durable stainless-steel connectors and heavy-duty booting extend the life of this versatile flexible cable assembly. The double shield includes a silver plated copper braid over a silver plated copper spiral strip providing excellent shielding effectiveness greater than 110 dB. Custom versions of this cable assembly along with the rest of L-com's RF cable assemblies can be built and shipped same day. Other available RF cable assembly value added services include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for custom cable quotes.
LMR-LW600-LC-FT
LMR-LW600-LC-FT coax cable from L-com is only one of a large number of radio frequency coaxial cable types specifically stocked to be ready for quick shipment. L-com LMR-LW600-LC-FT coax cable is manufactured in a flexible design and has a 50 Ohm impedance. This low loss flexible 50 Ohm coax cable LMR-LW600-LC-FT is constructed with a 0.590 inch diameter and Black PE jacket. LMR-LW600-LC-FT flexible 50 Ohm coax cable with PVC jacket is rated for a 5.8GHz maximum operating frequency. This 50 Ohm 0.590 inch diameter and low loss flexible coax cable is built with a double shield count and RF shielding of 90 dB. L-com LMR-LW600-LC-FT coax is constructed with Foam PE dielectric and a maximum operating temperature of +85 degrees C. Times Microwave LMR-LW600-LC-FT coax cable specs for this wire properties can be found on its RF coax cable LMR-LW600-LC-FT datasheet. LMR-LW600-LC-FT cable is part of more than one million RF, microwave parts in stock at L-com. This Times Microwave low loss LMR-LW600-LC-FT coax cable is ready to buy and can be shipped worldwide. L-com also maintains a wide selection of other radio frequency coaxial cable types that ship same-day from our warehouse as with the rest of our other RF/microwave components. * LMR™ is a trademark of Times Microwave Systems.
FMCN1691
RA 4.1/9.5 Mini DIN Male Low PIM Connector Solder Attachment for FM-1/4SFHC, SPP-250-LLPL, SPO-250, SPF-250 Cable
550T039Y3F0B1-04B
capots arrière D-Sub BANDING SPLIT BS TOP FRONT montage EMI
LCCA30335-FT1
L-com's LCCA30335-FT1 is a low loss 7/16 DIN male to N male right angle cable assembly using LMR-600 coax, 1 FT with Times Microwave components and ships same-day. The LMR-600 coax of this 7/16 DIN cable uses the PE (F) dielectric with a VoP of 87%, resulting in very low insertion loss compared to solid dielectrics. These flexible RF cable assemblies are ideal for applications where flexure is required. Our L-com 7/16 DIN to N cable assembly has a male to male gender configuration with flexible LMR-600 series coax and operates to 5.8 GHz. The double shield of this 7/16 DIN cable is layered by tinned copper braid over aluminum tape providing shielding effectiveness greater than 90dB. This right angle N cable interface on the LMR-600 coax allows for easier connections in tight spaces. *LMR™ is a trademark of Times Microwave Systems. Custom versions of this 7/16 DIN male to 7/16 DIN male cable, along with the rest of L-com's other RF assemblies, can also be built and shipped same day. Other available RF cable assembly value added services from L-com include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for testing or custom RF cable quotes. Part number LCCA30335-FT1 L-com Low Loss 7/16 DIN Male to N Male Right Angle Cable Assembly using LMR-600 Coax, 1 FT with Times Microwave Components data sheet PDF includes details of the RF product specifications, CAD drawing(s) and dimensions below.
Recherche MPN Prend en charge la correspondance exacte, par préfixe et partielle. ⌄
Avertissement
Cstone est une usine professionnelle, et non une société de négoce, spécialisée dans les connecteurs RF et coaxiaux, les adaptateurs et les assemblages de câbles, notamment N-type, BNC, SMA, SMP, SSMB et MMCX. Nous fabriquons les connecteurs selon des plans 2D ou des échantillons ; l’adéquation, le MOQ, le délai et les détails de production sont confirmés par RFQ. Cstone Technology n’est pas affiliée aux marques d’origine. Les noms de fabricants, marques déposées, symboles et références de pièces sont utilisés uniquement à des fins d’identification et de référence croisée. Les marques restent la propriété de leurs détenteurs respectifs. L’adéquation finale est confirmée par examen du plan/des spécifications lors du RFQ.