Produktdetails
50 Ohm 10 Watts Black Anodized Aluminum Heatsink 7/16 DIN Female RF Load Up To 7 GHz
Teilenummer (MPN)
Impedanz
50 Ohm
Frequenz
DC
Schnittstelle
7/16 DIN
kundenspezifische RF-Kabelbaugruppe nach Zeichnung für Produktions-Sourcing
Produktionsorientierte kundenspezifische RF-Kabelbaugruppe nach Zeichnung mit Kompatibilitätsprüfung, MOQ-Führung und Cost-down-Sourcing-Unterstützung.
Was vor dem RFQ vorzubereiten ist Klare Eingaben reduzieren Vermutungen und beschleunigen eine nützliche Antwort. ⌄
- • Teilen Sie die Referenz-MPN, das Gegenstück oder die Quellmarke mit, wenn es für die Prüfung relevant ist.
- • Fügen Sie BOM, Mengenaufteilung und Jahresbedarf hinzu, wenn das Projekt über den Prototypenumfang hinausgeht.
- • Legen Sie Zeichnung, Datenblatt oder kritische Anforderungen zu Impedanz, Frequenz, Montage und Beschichtung bei.
Bild
Zum Vergrößern klicken.
Specifications
| Schnittstelle | Terminations |
|---|---|
| Schnittstelle | RF Load |
| Schnittstelle | 7/16 DIN |
| Impedanz | 50 Ohm |
| Frequenz (max) | DC |
| Frequenz (max) | 7 GHz |
| Geschlecht | Female |
| Maximum VSWR | 1.25:1 |
| Maximum Power | 10 Watt |
| Category | Terminations |
Beschreibung
Aktuelle Referenzdaten für PE6141: 7/16 DIN · 50 Ohm · DC. Der Katalog listet die Konfiguration als: RF Load. Die Impedanz ist als 50 Ohm angegeben. Wenn dieser Parameter kritisch ist, bestätigen Sie ihn im RFQ erneut. Die Frequenz ist als DC angegeben. Die reale Betriebsgrenze hängt weiterhin von Baugruppe, Gegenstück und Einsatzumfeld ab. Wenn die Montage hier fehlt, bestätigen Sie sie aus der Zeichnung oder der Gegenstückanforderung. Nutzen Sie diese Seite zur Vorauswahl vor dem RFQ, nicht als endgültige Freigabe.
Nutzen Sie diese Seite für die Vorauswahl vor der RFQ. Lieferweg und MOQ 200+ Sonderfertigung werden nach Prüfung von Zeichnung/Spezifikation/BOM bestätigt.
Ähnliche Steckverbinder
Diese Modelle könnten ebenfalls interessant sein:
LCCA30189-FT3
L-com's LCCA30189-FT3 is a low loss 4.3-10 male to 4.3-10 male cable assembly using LMR-400 coax, 3 FT with Times Microwave components and ships same-day. The LMR-400 coax of this 4.3-10 cable uses the PE (F) dielectric with a VoP of 85%, resulting in very low insertion loss compared to solid dielectrics. These flexible RF cable assemblies are ideal for applications where flexure is required. Our L-com 4.3-10 to 4.3-10 cable assembly has a male to male gender configuration with flexible LMR-400 series coax and operates to 6 GHz. The double shield of this 4.3-10 cable is layered by tinned copper braid over aluminum tape providing shielding effectiveness greater than 90dB. *LMR™ is a trademark of Times Microwave Systems. Custom versions of this 4.3-10 male to 4.3-10 male cable, along with the rest of L-com's other RF assemblies, can also be built and shipped same day. Other available RF cable assembly value added services from L-com include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for testing or custom RF cable quotes. Part number LCCA30189-FT3 L-com Low Loss 4.3-10 Male to 4.3-10 Male Cable Assembly using LMR-400 Coax, 3 FT with Times Microwave Components data sheet PDF includes details of the RF product specifications, CAD drawing(s) and dimensions below.
LCCA30008-FT1
L-com Cable Assembly LCCA30008 is an N male to N female 1 foot cable using 402SS Series coax that ships same-day. L-com's flexible RF cable assemblies are ideal for applications where tight bends and flexure are required. This L-com N to N cable assembly has a male to female gender configuration with 50 ohm flexible 402SS Series coax and operates to 18 GHz. Highly durable stainless-steel connectors and heavy-duty booting extend the life of this versatile flexible cable assembly. The double shield includes a silver plated copper braid over a silver plated copper spiral strip providing excellent shielding effectiveness greater than 110 dB. Custom versions of this cable assembly along with the rest of L-com's RF cable assemblies can be built and shipped same day. Other available RF cable assembly value added services include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for custom cable quotes.
LMR-LW600-LC-FT
LMR-LW600-LC-FT coax cable from L-com is only one of a large number of radio frequency coaxial cable types specifically stocked to be ready for quick shipment. L-com LMR-LW600-LC-FT coax cable is manufactured in a flexible design and has a 50 Ohm impedance. This low loss flexible 50 Ohm coax cable LMR-LW600-LC-FT is constructed with a 0.590 inch diameter and Black PE jacket. LMR-LW600-LC-FT flexible 50 Ohm coax cable with PVC jacket is rated for a 5.8GHz maximum operating frequency. This 50 Ohm 0.590 inch diameter and low loss flexible coax cable is built with a double shield count and RF shielding of 90 dB. L-com LMR-LW600-LC-FT coax is constructed with Foam PE dielectric and a maximum operating temperature of +85 degrees C. Times Microwave LMR-LW600-LC-FT coax cable specs for this wire properties can be found on its RF coax cable LMR-LW600-LC-FT datasheet. LMR-LW600-LC-FT cable is part of more than one million RF, microwave parts in stock at L-com. This Times Microwave low loss LMR-LW600-LC-FT coax cable is ready to buy and can be shipped worldwide. L-com also maintains a wide selection of other radio frequency coaxial cable types that ship same-day from our warehouse as with the rest of our other RF/microwave components. * LMR™ is a trademark of Times Microwave Systems.
FMCN1691
RA 4.1/9.5 Mini DIN Male Low PIM Connector Solder Attachment for FM-1/4SFHC, SPP-250-LLPL, SPO-250, SPF-250 Cable
550T039Y3F0B1-04B
D-Sub-Rückenschalen BANDING SPLIT BS TOP FRONT Montage EMI
LCCA30335-FT1
L-com's LCCA30335-FT1 is a low loss 7/16 DIN male to N male right angle cable assembly using LMR-600 coax, 1 FT with Times Microwave components and ships same-day. The LMR-600 coax of this 7/16 DIN cable uses the PE (F) dielectric with a VoP of 87%, resulting in very low insertion loss compared to solid dielectrics. These flexible RF cable assemblies are ideal for applications where flexure is required. Our L-com 7/16 DIN to N cable assembly has a male to male gender configuration with flexible LMR-600 series coax and operates to 5.8 GHz. The double shield of this 7/16 DIN cable is layered by tinned copper braid over aluminum tape providing shielding effectiveness greater than 90dB. This right angle N cable interface on the LMR-600 coax allows for easier connections in tight spaces. *LMR™ is a trademark of Times Microwave Systems. Custom versions of this 7/16 DIN male to 7/16 DIN male cable, along with the rest of L-com's other RF assemblies, can also be built and shipped same day. Other available RF cable assembly value added services from L-com include connector orientation or clocking, heat shrink booting and custom labeling. RF testing can also be performed to document the electrical performance of your cable assembly. Contact a sales representative for testing or custom RF cable quotes. Part number LCCA30335-FT1 L-com Low Loss 7/16 DIN Male to N Male Right Angle Cable Assembly using LMR-600 Coax, 1 FT with Times Microwave Components data sheet PDF includes details of the RF product specifications, CAD drawing(s) and dimensions below.
MPN-Suche Unterstützt exakte, Präfix- und Teiltreffer. ⌄
Haftungsausschluss
Cstone ist eine professionelle Fabrik, kein Handelsunternehmen, für RF- und Koaxialsteckverbinder, Adapter und Kabelkonfektionen einschließlich N-Type, BNC, SMA, SMP, SSMB und MMCX. Wir fertigen Steckverbinder nach 2D-Zeichnungen oder Mustern; Passung, MOQ, Lieferzeit und Produktionsdetails werden per RFQ bestätigt. Cstone Technology ist nicht mit den Originalmarken verbunden. Herstellernamen, Marken, Symbole und Teilenummern werden ausschließlich zur Identifikation und zum Querverweis verwendet. Marken verbleiben im Eigentum der jeweiligen Inhaber. Die endgültige Eignung wird durch Prüfung der Zeichnung/Spezifikation im Rahmen der RFQ bestätigt.